View Profile: Indynic - Colt Forum
Tab Content
  • Indynic's Avatar
    Today, 04:55 PM
    Indynic replied to a thread Python 2020 in Python
    From an earlier post it went something like 1001 was the first “production” gun. 001-0050 were “pre-production.” And 0051-999 are reserved for...
    1298 replies | 158619 view(s)
  • Indynic's Avatar
    01-14-2020, 04:55 PM
    Indynic replied to a thread Python 2020 in Python
    I think you are right. This, and a lack of lubrication are what is causing the cylinder not to turn. It has to be something along those lines, as it...
    1298 replies | 158619 view(s)
  • Indynic's Avatar
    01-12-2020, 07:00 PM
    Indynic replied to a thread Python 2020 in Python
    What are the chances these failures stem from opening the cylinder with the hammer cocked? It specifically states not to do that in the factory...
    1298 replies | 158619 view(s)
  • Indynic's Avatar
    01-12-2020, 04:27 PM
    Indynic replied to a thread Python 2020 in Python
    He probably short stroked it. He’s an S&W shooter. The real dig was, “I wanna make sure it doesn’t seize up after 30 rounds like my S&W Model 19...
    1298 replies | 158619 view(s)
  • Indynic's Avatar
    01-12-2020, 06:28 AM
    Indynic replied to a thread 2020 Python Reports in Python
    Range Report: Dry fired (with snap caps) approximately 500 times prior to first range session. Rain here has been insane, so I was forced to go to...
    47 replies | 2468 view(s)
  • Indynic's Avatar
    01-10-2020, 06:47 AM
    To answer your initial question: “NO”
    7 replies | 283 view(s)
  • Indynic's Avatar
    01-10-2020, 06:45 AM
    Seems to me that the best way to clean up these burrs would be to run a countersink on it, basically making it a reverse crown like what is commonly...
    49 replies | 2107 view(s)
  • Indynic's Avatar
    01-09-2020, 08:11 PM
    Some people just have more dollars than sense....🤷‍♂️
    12 replies | 374 view(s)
  • Indynic's Avatar
    01-09-2020, 08:42 AM
    Most likely. When the counterbore cutters get dull, steel chips can hang on the side of the cutting edge and get pressed into the cutting surface.
    49 replies | 2107 view(s)
  • Indynic's Avatar
    01-08-2020, 08:47 PM
    Indynic replied to a thread 2020 Python Reports in Python
    Comparing the new Python side-by-side to the 686 & a newer 586 classic 6”, you can see where the extra money is. Fit is superb. Finish vs the 686...
    47 replies | 2468 view(s)
  • Indynic's Avatar
    01-04-2020, 09:52 PM
    Indynic replied to a thread Python 2020 in Python
    I’ve been trying to keep up. But, I haven’t seen details of the mentioned recall. What was the problem exactly?
    1298 replies | 158619 view(s)
  • Indynic's Avatar
    01-04-2020, 07:41 AM
    Indynic replied to a thread Python 2020 in Python
    I have wanted a Colt Python for half my life (20 years). When I was younger, I couldn’t afford them. Now, I could buy the older model, but I’d want a...
    1298 replies | 158619 view(s)
No More Results
About Indynic

Basic Information

Statistics


Total Posts
Total Posts
12
Posts Per Day
0.66
General Information
Last Activity
Today 06:26 PM
Join Date
12-30-2019
Referrals
0
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
We are not associated with Colt's Manufacturing LLC. We are an enthusiast site comprised of Colt Fans.
Powered by vBulletin® Version 4.2.3
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.
SEO by vBSEO ©2011, Crawlability, Inc.